1.75mm E3D V6 replacement nozzle – Printed Solid
By A Mystery Man Writer
Description
Replacement nozzles for E3D hot end available in 0.25-0.8mm orifice for 1.75mm filament. Note that we have moved the 3mm options here This is more than just a replacement, it is a serious upgrade that is also backwards compatible. This means that it works on E3D hotends older than the V6. It also works well on some
Replacement nozzles for E3D hot end available in 0.25-0.8mm orifice for 1.75mm filament. Note that we have moved the 3mm options here This is more than just a replacement, it is a serious upgrade that is also backwards compatible. This means that it works on E3D hotends older than the V6. It also works well on some other hot ends. We’ve tested it on the Reprapdiscount Hexagon, MP Mini, CR-10, and several others with good results. Note that the standard hot end is brass. This is the best choice for most materials. However, for abrasive materials such as carbon fiber, glow in the dark, and stainless and iron filled materials, the stainless nozzle will provide a longer life. However, while the stainless is a longer life, it is lower thermal conductivity than brass so higher temps and/or slower speeds may be required. The large bore has been elongated to give a minimum small diameter nozzle length. This reduces the potential for clogs. Nozzle Size Application ID Dots* 0.25mm Highest Precision - Slower Prints 0 0.30mm 1 0.35mm Slight Increase in Precision 2 0.40mm Balanced Nozzle - Supplied by Default 3 0.60mm Our Preferred Minimum for Wood Filled Filament 4 0.80mm Lower Precision - High Speed, Higher Strength 5 * Dots are machined onto the hex-flats of the nozzles for easy identification. Sanjay did a perfect job of explaining it, so we’ll just repeat his words! From the E3D Blog: Nozzle Specificity and Indentifiability. While we were in the process of going over the nozzle we thought we’d address making them easily identifiable on a per-size basis. It’s fairly obvious whether a nozzle is 1.75mm or 3mm, but telling the difference between a 0.35mm and a 0.40mm is incredibly hard, and that’s before they get covered in plastic. To that end we have added spots drilled onto the hex flats of the nozzles, the number of which corresponds to a specific size of nozzle. The more dots the bigger the nozzle. We did consider using a binary code, but decided that we didn’t need 64 different sizes of nozzles in the end – maybe one day. When a nozzle is printing it is not only outputting a stream of plastic, but also flattening it into its final stadium cross sectional shape. The width of this printed track is wider than that of the nozzles small diameter hole, as such the nozzle tip needs to have a flat on it that is at least as wide as the widest sensible track width. Because the widest sensible track width varies depending on the nozzle diameter it logically follows that the tip flat diameter should vary with the nozzle diameter. Phwwoooar look at that proportional orifice-tip-flat relationship! This means that with our larger 0.60mm and 0.80mm nozzles you can lay down fatter wider layers than ever before. This is great for large fast printing of super-strong objects, Nylons in particular benefit from being printed from big nozzles. Additionally you can create beautiful very glassy looking objects with big layers of PET type materials like _XT , T-Glase and Polycarbonate. **edit: A large diameter nozzle is also absolutely awesome for printing filled materials like woodfill and carbon fiber PLA. For our smaller nozzle this means you can get even greater resolution and print smaller details and features in your objects. The smaller tip flat allows you to put down those small features and details without an over sized tip flat smudging the tracks adjacent to what is being printed. These nozzles are also backward compatible with v5 and v4 so you can use them on existing hotends if you want to get some proportional orifice-tip-flat relationship goodness in your life without swapping out the whole hotend. Can't decide? Why not try the Fun Pack This pack contains: 0.25mm 0.30mm 0.35mm 0.50mm 0.60mm 0.80mm E3D Nozzle Spanner
Replacement nozzles for E3D hot end available in 0.25-0.8mm orifice for 1.75mm filament. Note that we have moved the 3mm options here This is more than just a replacement, it is a serious upgrade that is also backwards compatible. This means that it works on E3D hotends older than the V6. It also works well on some other hot ends. We’ve tested it on the Reprapdiscount Hexagon, MP Mini, CR-10, and several others with good results. Note that the standard hot end is brass. This is the best choice for most materials. However, for abrasive materials such as carbon fiber, glow in the dark, and stainless and iron filled materials, the stainless nozzle will provide a longer life. However, while the stainless is a longer life, it is lower thermal conductivity than brass so higher temps and/or slower speeds may be required. The large bore has been elongated to give a minimum small diameter nozzle length. This reduces the potential for clogs. Nozzle Size Application ID Dots* 0.25mm Highest Precision - Slower Prints 0 0.30mm 1 0.35mm Slight Increase in Precision 2 0.40mm Balanced Nozzle - Supplied by Default 3 0.60mm Our Preferred Minimum for Wood Filled Filament 4 0.80mm Lower Precision - High Speed, Higher Strength 5 * Dots are machined onto the hex-flats of the nozzles for easy identification. Sanjay did a perfect job of explaining it, so we’ll just repeat his words! From the E3D Blog: Nozzle Specificity and Indentifiability. While we were in the process of going over the nozzle we thought we’d address making them easily identifiable on a per-size basis. It’s fairly obvious whether a nozzle is 1.75mm or 3mm, but telling the difference between a 0.35mm and a 0.40mm is incredibly hard, and that’s before they get covered in plastic. To that end we have added spots drilled onto the hex flats of the nozzles, the number of which corresponds to a specific size of nozzle. The more dots the bigger the nozzle. We did consider using a binary code, but decided that we didn’t need 64 different sizes of nozzles in the end – maybe one day. When a nozzle is printing it is not only outputting a stream of plastic, but also flattening it into its final stadium cross sectional shape. The width of this printed track is wider than that of the nozzles small diameter hole, as such the nozzle tip needs to have a flat on it that is at least as wide as the widest sensible track width. Because the widest sensible track width varies depending on the nozzle diameter it logically follows that the tip flat diameter should vary with the nozzle diameter. Phwwoooar look at that proportional orifice-tip-flat relationship! This means that with our larger 0.60mm and 0.80mm nozzles you can lay down fatter wider layers than ever before. This is great for large fast printing of super-strong objects, Nylons in particular benefit from being printed from big nozzles. Additionally you can create beautiful very glassy looking objects with big layers of PET type materials like _XT , T-Glase and Polycarbonate. **edit: A large diameter nozzle is also absolutely awesome for printing filled materials like woodfill and carbon fiber PLA. For our smaller nozzle this means you can get even greater resolution and print smaller details and features in your objects. The smaller tip flat allows you to put down those small features and details without an over sized tip flat smudging the tracks adjacent to what is being printed. These nozzles are also backward compatible with v5 and v4 so you can use them on existing hotends if you want to get some proportional orifice-tip-flat relationship goodness in your life without swapping out the whole hotend. Can't decide? Why not try the Fun Pack This pack contains: 0.25mm 0.30mm 0.35mm 0.50mm 0.60mm 0.80mm E3D Nozzle Spanner
Original E3D v6.1 24V Hotend for Prusa i3 MK3 – Voxel Factory
3D Printer Nozzle Stainless Steel 0.2mm-1.2mm Extruder Print Head for V5 V6 Lot
From E3D:, Our most advanced nozzle yet. ObXidian is our latest abrasive Nozzle offering, specifically designed for printing fibre-filled polymers.
E3D ObXidian Nozzle for V6 Style
2pcs E3D V6 Hardened Steel Nozzle V5 V6 Hotend M6 Thread All Metal Nozzles For Titan Hotend For 1.75mm Filament 3D Printer Parts - AliExpress
E3D MK8 Brass Nozzles
V6 E3D Clone Stainless Steel Nozzle 1.75mm-0.6mm (5 Pack) - 3D Printing Canada
1.75mm E3D V6 replacement nozzle – Printed Solid
V6 Plated Copper Nozzles, These nozzles are engineered for ultimate high temperature performance. Made from a special high temperature copper-alloy
E3D V6 Nozzle - Nickel Plated Copper - 1.75mm
1/3Pcs E3D V6 MK8 Clone-CHT Tip Nozzle PTFE Brass 0.4mm High Flow Nozzles for 1.75mm Filament Fast Speed 3D Printer Accessories. - AliExpress
Nozzle 0,6 mm E3D V6 - filament 1,75mm - hardened steel Botland - Robotic Shop
Choose between 3 materials for your next E3D Volcano nozzle, Brass, High-performance brass nozzles for your Volcano HotEnd. From super-fine to
1.75mm E3D Volcano replacement nozzle
A full collection of E3D-V6 Ecosystem Brass nozzles, set in a soft foam cushion for protection. Print all the things in all the resolutions!, Suitable
E3D V6 Hotend Nozzle Fun Pack - 1.75mm – Printed Solid
E3D V6 Nozzle - Nozzle X - 0.6mm - 1.75
from
per adult (price varies by group size)